Benutzer-Werkzeuge

Webseiten-Werkzeuge


wolf_en

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen gezeigt.

Link zu der Vergleichsansicht

wolf_en [22.12.2016 14:24] (aktuell)
Dirk Römmen angelegt
Zeile 1: Zeile 1:
 +====== Wolf ======
 +
 +The Wolf driver allows it to transfer any data over the implemented Wolf protocol to Wolf heating and cooling devices.
 +
 +The name of this driver is: wolf\\
 +The routing address of the first driver is 1500\\
 +The data point file name for the first driver is: wolf1.txt\\
 +The driver configuration file name for the first driver is: wolf1.cfg\\
 +
 +For the Wolf driver as well as all other gateway drivers the data point definitions are as follows:
 +
 +^Type  ^Description ​ ^
 +^  M  |Integer value (binary data points, counters) which can/shall only be read by the gateway ​ |
 +^  S  |Integer value which can be either read or written by the gateway. (to M-BUS writing is not possible) ​ |
 +^  X  |Floating point value (with decimal place) which can/shall only be read by the gateway ​ |
 +^  Y  |Floating point value (with decimal place) which can be either read or written by the gateway. (to M-BUS writing is not possible) ​ |
 +^  A  |String, is used e.g. with BACnet Trends and ESPA4.4.4 data points ​ |
 +
 +The Wolf addresses are defined as follows:\\
 +<data point-type>​ <​station-id>​.<​data point-id>​
 +
 +data point-type: failure, point\\
 +station-id: 0 - 255 (0 is the locale station of the driver)\\
 +data point-id: 0 - 65534\\
 +
 +
 +=== data point-type: "​failure"​ ===
 +[M failure 0]\\
 +name = connection lost to station 0\\
 +query = pe\\
 +
 +
 +=== data point-type: "​point"​ ===
 +[S point 0.1]\\
 +name    = Error\\
 +query   = pe\\
 +nomval = 0\\
 +
 +[S point 0.2]\\
 +name    = mode of operation\\
 +query   = pe\\
 +nomval = 3\\
 +\\
 +
 +==== Start options of this driver in section [WOLF]: ====
 +
 +^Name: ​ ^Type  ^Range ^Description
 +^IpAddr|string|0.0.0.0|IP listening address of driver
 +^IpPort|number|0-65535|IP listening port of driver
 +\\
 +
 +==== Options of this driver in section [STATION_<​no>​]:​ ====
 +
 +^Name: ​ ^Type  ^Range ^Description
 +^IpAddr|string|0.0.0.0|IP address of driver
 +^IpPort|number|0-65535|IP port of driver
 +\\
 +
 +==== Example wolf1.cfg-file:​ ====
 +
 +[WOLF]\\
 +IpAddr = 192.168.0.249\\
 +IpPort = 4000\\
 +
 +[STATION_1]\\
 +IpAddr = 192.168.0.249\\
 +IpPort = 4096\\
 +
 +[STATION_2]\\
 +IpAddr = 192.168.0.249\\
 +IpPort = 4097\\
  
wolf_en.txt · Zuletzt geändert: 22.12.2016 14:24 von Dirk Römmen